Nozzle Features
- Internal mix
- Flow rates from 32 L/hr to 840 L/hr
- Very fine atomisation
Safer and affordable paper nozzle solutions
Since 1988, Spray Nozzle Engineering, supports the pulp, paper, packaging, and fibre recycling industries, supplying spray nozzles from BETE as well as developing a range of paper nozzles.
Spray Nozzle Engineering’s latest paper nozzle innovation is the Snap Disc™, designed and for all Australian, New Zealand and international paper mills.
The original Snap Disc™ shower nozzle change out system has saved customers thousands of dollars in lost time and wages. No other similar system on the market is as fast or as easy to use. Holding the ergonomic adjustment tool with just one hand, the operator can change out multiple nozzles in a fraction of the time of conventional nozzle change out systems.
With its patented threadless design, the new Snap Disc™ is the best choice for spray bars that are causing problems with nozzle change outs and for new installations to eliminate the costly exercise of evaluating retrofits when the installed system is found to contribute to slow nozzle change outs and impact production.
The Snap Disc™ is safe, secure and simple to use. No tools are required and the locating disc locks in to alignment in the correct orientation every time due to single direction rotation, virtually eliminating incorrect alignment and safety hazards.
Its secure alignment and quick release mechanism ensure consistent, and rapid change out performance on every spray nozzle. Encompassing a locating disc, flat flan or needle spray disc, gasket and weld base, in a large selection of pipe diameter fittings and seal options, the Snap Disc™ is the most comprehensive and biggest cost-saving shower nozzle change out system available.
Spray Nozzle Engineering manufactures other solutions for the pulp and paper mill industries such as: Shower Disc Nozzles and the Ruby Needle Jet Shower Nozzles
See our pulp and paper mill nozzles gallery
Examples of pulp and paper making processes in which BETE spray nozzles are used:
- Debarking
- Dust control
- Washing and moistening logs
- Pulp washing
- Pulp bleaching
- Foam control
- White water cleaning of wire and felts
- Humidification
- Heat recovery
- Odour control
- Air pollution control
- Cooling ponds
- Water pollution
-
-
Nozzle Features
- Internal mix
- Flow rates from 15.5 L/hr to 840 L/hr
- Very fine atomisation
-
To enhance and protect Silvent's range of high force blowing guns.
- Patented air induction shroud assisting blowing efficiency
- Unique protective cover for standard
- Food grade heavy duty stainless construction
- Optional rubber coating for impact resistance and longer life
-
Custom design, manufacturing and in-house service/repair of lance pipework and spray bars
Spray Nozzle Engineering manufacture injection quills, also known as spray quench, spray bars or injection lances. We design and supply custom made spray bars based on the type of fluid and its velocity. During the design process we also consider factors such as the gas pressure, inlet temperature, target temperature, inlet humidity and gas flow. We work in conjunction with a team of engineers that design solutions based on water conditions, pressure, temperature and cleanliness. The lances are used in gas scrubbing, refineries, chemical plants, among a long list of industries. Spray Nozzle Engineering works to your requirements, from the most simple to the most complex. -
Nozzle Features
- One-piece construction
- Flow rates from 0.051 L/Min to 757 L/Min
- Clog-resistant
- 3/8″ FFs in Brass is available with UL approval
- For FM-approved flat fan nozzles, see the AFF series
- Extra-wide 145° spray angle
- Medium-impact spray
- Coarse atomisation
-
L Nozzles
- A series of small spiral nozzles with orifice diameters of 0.04" (1.02 mm) to 0.12" (3.05 mm)
- Male connection
- Spray Pattern of the L Evaporative
- Cooling Nozzle: Hollow Cone Fog, nearly as fine as P series
- Common Materials:
- 303, 310, 316, 317L, 321, 347, Brass, Nickel Alloy C-22, Nickel Alloy C-276, PTFE
-
CIP spray nozzles designed to provide superior tank cleaning results at low operating pressures. Your solution to cleaner tanks with less water. Use M-SERIES tank washers with patented Flow Step Technology as a direct replacement for spray balls, delivering more efficient spray distribution, greater impact and faster C.I.P cycles. This means less waste water and low-chemical treatment costs, saving you time and money.
-
MaxiPass low flow (MPL) nozzles: Low flow maximum free passage full cone nozzles
- Ultimate clog-resistant design with largest free passage available in a full cone nozzle
- Two unique S-shaped internal vanes, as opposed to x-vane style nozzles, allow maximum free passage of particles
- High energy efficiency
- Easily handles dirty, lumpy liquids
- Male connections
- High reliability spray performance under the most difficult conditions
-
MicroWhirl® (MW) Nozzles atomising, evaporative cooling, misting, and fogging nozzles
- Outstanding atomization
- Rugged pinless design
- Drip-free performance
- 70 micron polypropylene filter
- Safety wire hole available
- U.S. Patent #7198201
- Minimum operating pressure 100 psi (7 bar)
- Mist at low pressure; fog at high pressure
- Common Materials:
- 303, 316, Nickel Alloy C-276
-
NCS nozzles
- Takes no more room than pipe plug, yet performs like full-size nozzle
- Small projection
- Can be used with standard pipe couplings to form female nozzle, with elbows to form right angle nozzle, or with tees or crosses for multiple installations
- Male connection
- Metal and plastic materials
- Common Materials:
- 316, A494 CU5MCuC (cast Nickel Alloy 825), A494 CW2M (cast Nickel Alloy C-276), A494 CW6MC (cast Nickel Alloy 625), A494 CX2MW (cast Nickel Alloy C-22), Brass, Duplex 2205, Polypropylene, PTFE, PVC
-
- One-piece construction
- No internal parts
- Sizes for all applications
- Male connection
- High impact
- Uniform distribution with tapered edges for overlapping sprays
- Extra-wide angles available
- Common materials
- 303, 316, Brass, PVC, PTFE
-
PJ Nozzles
Design Features
- High energy efficiency
- No whirl vanes or internal parts
- 1/8" or 1/4" male connection
- 100-mesh screen, 20 micron paper filter or 70 micron polypropylene filter optional
Spray Characteristics
- Finest fog of any direct pressure nozzle
- Produces high percentage of droplets under 50 microns
- Common Materials:
- 303, 310, 316, 321, 347, Brass, Nickel Alloy C-276
-
- Unique no adhesive construction
- Resist premature orifice dislodgement
- Conventional washer and o-ring seal options
- Bullet design & extension tube disc option
-
- Patented orifice insert system
- Mechanically assembled, no adhesive construction
- Longer life and pressure range
- Optional filter screens for all pipe sizes
-
- Precision stainless shower nozzle
- Universal Fit
- Use in Snap-Disc easy fit shower head system
- Various flow sizes and profiles available
-
Nozzle Features
- Adjustable swivel joints allow custom alignment of spray nozzles
- Leak-proof design
- Other materials available upon request
-
- Eliminates disc misalignment
- No threads no tools
- Easy pre-assembly
- Positive seal / location
- Can only be installed one way
-
Nozzle Features
- Multiple flat fan patterns
- Flow rates from 9.16 L/Min to 618 L/Min
- Solid one-piece construction
-
TF Nozzles: Spiral spray, fogging, misting, and evaporative cooling nozzles in a wide range of flows and angles; full cone nozzles, hollow cone nozzles, misting nozzles
Non-clogging nozzles: TF Spiral Spray Nozzle
- The original spiral nozzle invented by BETE
- Also referred to as pigtail nozzles, corkscrew nozzles and/or helix nozzles
- High energy efficiency
- One-piece/no internal parts
- Clog-resistant performance
- High discharge velocity
- Male connection standard; female connection available by special order
- The TF24-150, the TF8NN, and TF8FCN (in brass) are FM approved
- Wide range of flow rates and spray angles
- Fine atomisation
-
WL Whirl nozzles
- Advanced whirl plate design produces uniform coverage
- Male and female connections
- Medium to coarse atomisation
- Common Materials:
- 303, 316, Brass, CPVC, Duplex 2205, Nickel Alloy 625, Nickel Alloy 825, Nickel Alloy C-22, Nickel Alloy C-276, Polypropylene, PTFE, PVC, PVDF
-
WTX nozzles
- Tangential whirl
- Oversized body for extended life
- Male and female connections
- Large free passage
- Common Materials:
- 303, 316, Brass, Duplex 2205, Nickel Alloy 625, Nickel Alloy 825, Nickel Alloy C-22, Nickel Alloy C-276
-
WTZ nozzles
- No internal parts, clog-resistant
- Uniform distribution
- Male and female connections
- Large free passage
- Common Materials:
- 303, 316, Brass, Duplex 2205, Nickel Alloy 625, Nickel Alloy 825, Nickel Alloy C-22, Nickel Alloy C-276, PVC
